Cummins B series Adapter, Flywheel and Ft mounts, to International IH 66, 86, 88

Description

REVISED 1/16
DETAILS ABOUT OUR THREE PIECE KIT
Adapter plate & new 14" flywheel and front mounts to repower  IH 66,  86 and (9) models of the 88 series diesel powered tractors with Cummins 5.9 / 6-BT engines.
Our plate is a precision built piece that fits the profile of the bell housing properly and looks like an original part.  It is approx 2 inches wider than the plate we build for the 06 and 56 series tractors.
You can be assured the alignment is correct, and that the plate will put your frame rails in the correct spot to make your hoods and sheet metal line up correctly and the engine will look like it was there from new.
They are built on a 2015 model CNC machine and are designed to use the original dial pins on the bell housing side and the Cummins style pins on the engine side so that everything runs true.
This kit is built with pride here in the US and  is designed for appearance as well as strength.  Will be a repower that you can be proud of and that will over the long haul pay for itself in fuel savings,
will save money on repair cost and will add value to the tractor in the coming years.
The plate is built of Aluminum alloy or steel (By special order)  and comes with a new 14 inch flywheel and front mounts,
This flywheel is built so that you can run your starter in all applications named here as the ring gear is in the exact location as factory was! We use stock IH clutch parts including the throwout and pilot bearing.
These are common over the counter parts from your local dealer, or at any number of aftermarket parts yards and clutch rebuilders. We use the same 14 inch clutch kit as a 1066  which had 12 springs
and therefore an easier pedal, or the1086 which had a 15 spring pressure plate and works best with a hydraulic clutch assist or the setup from a 1586 which has the bigger splines on the clutch and IPTO drive.
The choice on the clutches should be made based upon what job you are going to build it for and on how much pedal you can push.
ALL ORIGINAL ADJUSTMENTS AND CLUTCH CONTROLS ARE RETAINED IN EVERY CASE.
If you are starting with a tractor that had the 12 inch flywheel set up like the 7,8 and 9 in the 66 and 86 series or the 30, 32 and 3688 series;  the 14" setup will be
an upgrade and a significant improvement over the original clutch.
This kit  (plate, mts and the larger 14 inch wheel) fits ALL of  the models as detailed and listed below.
766-D, 866, 966 gear drive, 1066 gear drive, 1466, 1566, 786, 886, 986, 1086, 1486, 1586,
3088, 3288, 3688, 3388, 3588, 3788, 6388, 6588, and 6788,
IF YOU HAVE A 766 WITH A GAS ENGINE OR ANY OF THE IH  LARGE FRAME TRACTORS RUNNING A HYDRO TRANSMISSION
PLEASE SEE OUR OTHER LISTINGS OR CALL FOR INFORMATION,  WE HAVE THE KITS AVAILABLE.
THESE PARTS ARE ALSO SOON TO BE OFFERED INDIVIDUALLY ON THIS SITE,  EMAIL US IF YOU ARE UNCERTAIN OF THE APPLICATION
ALL OF THE TRACTORS
LISTED
ABOVE
HAVE
THE LOWER WATER RETURN OUTLET ON THE CORRECT (RIGHT) SIDE.  YOU WILL BE ABLE TO USE YOUR ORIGINAL RADIATOR.
WE ARE A GOOD SOURCE FOR NEW HIGH QUALITY RADIATORS AND AT SPECIAL PRICES WHEN BOUGHT WITH A KIT.  WE CAN SELL MOST OF THEM FOR APPROX 0
WE ALSO  HAVE A COMPLETE LINE OF COMPETITIVELY PRICED CLUTCHES IN STOCK HERE IN PA
AND FOR THOSE THAT WANT TO HOT ROD OR TRACTOR PULL YOU  WILL BE GLAD TO KNOW THAT MOST OF THE
HIGH PERFORMANCE TA'S AND DOUBLE or TRIPLE DISC CLUTCHES WE SELL FOR IH ENGINES ARE USABLE AND AVAILABLE TO WORK WITH THIS CONVERSION
ALUMINUM PLATE WEIGHS APPROX 40 LBS,  STEEL WEIGHS CLOSE TO 100 LBS
Fly wheel makes second package of approx 80 lbs, front mounts weigh about 7 lbs
A GOOD RUNNING 5.9 WILL GIVE A 400 SERIES A RUN FOR ITS MONEY IF SET UP PROPERLY
AND WILL OUT LAST AND BURN LESS FUEL PER HOUR ITS WHOLE LIFE!!
THE 5.9
WITHOUT
A TURBO IS GREAT UP TO ABOUT 90 HP BUT IT MAKES PRETTY GOOD TORQUE
IS AN EASY INSTALL AND YOU MAY FIND IT TO BE AN ACCEPTABLE  REPLACEMENT FOR 766 OR 886
THE 5.9
WITH
A TURBO AND INTERCOOLER IS WELL KNOWN FOR ITS ABILITY TO MAKE 150 HP+
AND BE EFFICIENT.  OR TO MAKE 240 PLUS IF THE FUEL PUMP IS SET PROPERLY.! SEEMS THE SKY IS THE LIMIT ON PERFORMANCE
THESE LITTLE ENGINES WILL SURPRISE YOU AND CAN GIVE A 436T A GOOD RUN FOR ITS MONEY WHILE BURNING A LOT LESS FUEL
SEE OUR OTHER LISTINGS FOR INFO ABOUT OTHER  UPGRADES FOR IH TRACTORS
We have a kit available for the small frame tractors like the 544, 656,666, 686 etc  as well as a kit that makes it possible to bolt a B series into the M, SM, SMTA,
400, 450 560, 660.in gas or diesel, uses a modified 12" flywheel and a factory clutch.
FOR PULLERS WE HAVE AN ELEVEN INCH STEEL SETUP THAT IS AVAILABLE IN DOUBLE OR TRIPLE DISC WITH CUMMINS PATTERN
stay tuned or contact us for more info
717-464-2874
We will ship by UPS in 2 pkgs
If you are a dealer and are interested in several sets you may wish to call or contact us by e/mail or through E/Bay.
Volume discounts available!!